Jeya Vardhan
← All workHardware · Feb 2026

Robo soccer bot

A four-wheel-drive competition robot driven by an Arduino, two 43 A motor drivers and a 2.4 GHz radio.

Robo soccer bot, cover image
Top view of the four-wheel robot: an Arduino drives two BTS7960 motor drivers from a 2.4 GHz radio receiverTOP VIEW · 4WD, DIFFERENTIAL STEERINGBALLLEFTFASTERRIGHTSLOWERBTS796043 A · LBTS796043 A · RATMEGA328PARDUINO UNOFS-IA6B2.4 GHZ RX3S LIPO11.1 VCH1 · THROTTLEPULSE 1000–2000 µSPWM IN → MOTOR SPEED
Fig. 1 — How it works

Overview

The Robo Soccer Bot repository documents the complete end-to-end engineering journey of designing, fabricating, wiring, and programming a competition-ready mobile robot built for competitive robotics tournaments.

The robot features high-torque differential drive mechanics, high-current power switching, real-time 2.4GHz RC radio decoding, and firmware written in C++ for the Arduino platform.

  • Primary Controller: Arduino Uno (ATmega328P)
  • Power Electronics: Dual BTS7960 43A High-Power H-Bridge Motor Drivers
  • Actuators: 4x High-Torque Metal Gear DC Motors (300 RPM)
  • Power Supply: 3S Lithium Polymer (LiPo) Battery (11.1V, high discharge C-rating)
  • Control Interface: FlySky FS-i6 2.4GHz 6-Channel Transmitter & FS-iA6B Receiver

Hardware Architecture & Electrical Challenges

[ FlySky 2.4GHz Transmitter ]
              │ (RF Signal)
              ▼
[ FlySky FS-iA6B Receiver ] 
              │ (PWM Channels)
              ▼
    [ Arduino Uno Microcontroller ]
              │ (Direction Pins + PWM Speed)
              ├──────────────────────────────┐
              ▼                              ▼
[ Left BTS7960 Driver (43A) ]   [ Right BTS7960 Driver (43A) ]
              │                              │
              ▼                              ▼
    [ 2x Left DC Motors ]          [ 2x Right DC Motors ]
              ▲                              ▲
              └──────────────┬───────────────┘
                             │
                  [ 3S LiPo Battery 11.1V ]

1. High-Current Inductive Spike Protection

Four 300 RPM DC motors drawing stall currents under rapid direction reversal can easily induce destructive back-EMF voltage spikes and brown out the 5V logic rail.

  • Utilized industrial-grade BTS7960 H-bridges featuring integrated heatsinks and MOSFET thermal shutdown protection.
  • Separated high-power motor ground returns from sensitive microcontroller signal grounds (common-point star grounding).

2. Microsecond PWM Signal Decoding

The Arduino firmware captures pulse-width modulation signals (1000µs – 2000µs range with a 1500µs neutral deadzone) directly from the FlySky receiver channels.

  • Implemented deadband thresholding in C++ (abs(pwm - 1500) < DEADZONE) to eliminate motor hum and jitter while resting at neutral stick positions.
  • Mapped analog stick deflections into differential steering velocity curves:
int forwardSpeed = map(ch2_pulse, 1500 + DEADZONE, 2000, 0, 255);
int turnOffset   = map(ch1_pulse, 1000, 2000, -128, 128);

int leftMotorPWM  = constrain(forwardSpeed + turnOffset, -255, 255);
int rightMotorPWM = constrain(forwardSpeed - turnOffset, -255, 255);

Verification & Status

  • Status: Fabricated, programmed, and field-tested in live competition matches.
  • Documentation: Includes complete schematic wiring diagrams, hardware component breakdowns, and firmware revision history in the repository.